This installation is for a HO-Scale Life Like Proto 2000 GP30.
HO-Scale Life Like Proto 2000 GP30 shown prior to installation.
To start off this install, we must first remove the front and rear coupler screws highlighted above and their housings.
With the couplers removed, while gently pulling outwards at each end and along each side of the frame, lift the shell off of the frame.
Take care to release the handrails as you lift off the shell so they don't break.
The Life Like Proto 2000 GP30 shown with the shell off. Remove the two screws located on the front left and rear right of the original lighting board as highlighted above in red.
Remove wires from the original lighting board and remove it from the chassis.
To allow a space for the motherboard and speaker, the frame must also be milled square above the original brush bracket as highlighted above to keep all the
components below the original top of the frame.
Trim the front track pick up post as shown above in blue to allow space for the KA4 Keep Alive® installation. With this trimmed,
resolder one side of the track connection wire to it. Remove and discard the original 1.5 V bulbs. For this installation, they will be replaced with a LEDs
inserted into the original housing.
With the original lighting board removed and above steps completed, trim, tin or lengthen the wires as necessary.
To recreate the second side of the track pickup, tap a small hole and insert this connection at the rear of the frame as shown above.
Insert the new LEDs into the original locations, securing them with a small dab of hot melt glue and solder the wire leads to the motherboard according to the included wiring diagram.
We have found that LED light output is brightest when shinning directly into the end of the light tube, but in some circumstances they may be placed along the length
of the tube as well with satisfactory results. In doing so, white light LED output would be least affected, while non white LED output will be more affected by placement.
TCS motherboards include on board current limit resistors for LED use. There is no need to apply external resistors for LED use.
Next, using hot melt glue or double sided foam tape, secure the KA4 Keep Alive® to the front of the frame as shown. Then using double sided foam tape, with
the 35mm X 16mm WOWsound speaker inserted into the UNIV-SH1-C enclosure, mount this assembly to the frame in front of the screw. Lay the wires leading
forward into the milled frame channel to secure them underneath the motherboard.
If your speaker enclosure installation covers the portholes on the enclosure, we recommend adding new port hole(s) similar to the original porting. Be sure that the new portholes are the same size and amount of the original and are vented freely into the locomotive We have found introducing a port of the correct size greatly increases the volume and sound quality of the installation. Too much or too little porting decreases the sound quality.
Attach the AS-MB2 NC to the frame with double sided foam tape and solder the motor, track pickup, KA4 and speaker wires according to the included wiring diagram.
NOTE: In this installation, the open fans on the roof have loose fan blades. In order to prevent vibration which could compromise the sound quality,
we recommend that you add a small drop of model glue to the junction of the fan blades and spindle to prevent this movement.
You can now plug in your WOW121 decoder.
Lastly, in order to keep the wires neat and prevent possible shorts, lace the wires into a bundle using lacing cord.
Now you can close up the locomotive and reinstall the coupler assemblies. Be sure to be mindful of wire routing and reassembly of the shell as to not damage
or foul the installation. Your Life Like Proto 2000 GP30 is now WOWSound equipped and ready to roll!
Important Soldering Tip
Please do not use any flux either liquid or paste on the mother board. It will damage it. Use only Rosin core solder approved for electronics use.
We recommend to use only Kester "44" rosin core, SN63PB37, .015" diameter, part number 24-6337-0007.
This can be ordered from Techni-Tool under Techni-Tool part number 488SO157
Other solder tips
When stripping wire, only strip a tiny little bit of the insulation. Strip no more then a 1/64 of an inch. When the wire gets tinned with solder, the insulation will shrink back more. Try to not expose any more wire then half the length of the solder pad at most. In no case should solder or exposed wire wire ever be outside the boundary of the the solder pad you are attaching a wire to.
Click here for important information on properly Stripping and Tinning wire
In order to keep the wires neat and prevent possible shorts, we recommend lacing the wires into a bundle using lacing cord. Lacing cord is a wax impregnated string used for wire bundling and making harnesses. There are many choices of lacing cord available from Digikey www.digikey.com.
We use part number 802534B BK032-ND