This installation is for a HO-Scale Life Like Proto 1000 RS-2 using a TCS WOW101 Diesel Decoder, KA4 Keep Alive®
and UNIV-SH4-C WOWSpeaker kit by TCS.
HO-Scale Life Like Proto 1000 RS-2 shown prior to installation.
To start off this install, we must first remove the front and rear coupler screws highlighted above and their housings.
With the couplers removed, while gently pulling outwards at each end and along each side of the frame, lift the shell off of the frame.
Take care to release the handrails as you lift off the shell so they don't break.
The Life Like Proto 1000 RS-2 shown with the shell off. Remove the the wires from the original lighting board and then the four screws whose locations are highlighted above in red. Remove the board from the chassis. At this time, remove also the original LEDs and place them aside for reinstallation later.
With the original lighting board removed, trim, tin or lengthen the wires as necessary.
In this installation as the shell is very close fitting, it is necessary to trim off flush the original lighting board mounting tabs as highlighted above in red to
allow space for the components to be installed.
Using double sided foam tape, mount the WOW101 Diesel Decoder to the frame as shown above. Plug in the harness connectors and trim the harness wires to length.
Wire splice in the track and motor pickup wires to the WOW101 Diesel Decoder.
Shrink tube statement: Using small lengths of TCS 3/32" and 3/64" shrink tubing, insulate these solder leads.
Next, using hot melt glue, mount the KA4 Keep Alive® behind the front LED mount and with the 25mm X 14mm WOWSound speaker inserted into the UNIV-SH4-C
enclosure, mount this assembly tightly behind the KA4, keeping them both in place. Secure the speaker enclosure to the frame using hot melt glue.
It is important to mount this speaker flush with one side edge of the frame below to allow a space for future routing the wires along side of the speaker enclosure.
NOTE: You must be very careful to avoid getting glue on the speaker cone. Glue on the speaker will ultimately cause it to produce no sound and fail.
If your speaker enclosure installation covers the portholes on the enclosure, we recommend adding new port hole(s) similar to the original porting. Be sure that the new portholes are the same size and amount of the original and are vented freely into the locomotive We have found introducing a port of the correct size greatly increases the volume and sound quality of the installation. Too much or too little porting decreases the sound quality.
Using a small dab of hot melt glue, replace the LED lights in the front and rear and splice the wires into the harness as shown.
With using LEDs and the WOW 101, it is necessary to add in a 1/6w 1k ohm resistor as highlighted above in red to these wire leads.
Lastly, in order to keep the wires neat and prevent possible shorts, lace the wires into a bundle using lacing cord.
Now you can close up the locomotive and reinstall the coupler assemblies. Be sure to be mindful of wire routing and reassembly of the shell as to not damage
or foul the installation. Your Life Like Proto 1000 RS-2 is now WOWSound equipped and ready to roll!
Important Soldering Tip
Please do not use any flux either liquid or paste on the mother board. It will damage it. Use only Rosin core solder approved for electronics use.
We recommend to use only Kester "44" rosin core, SN63PB37, .015" diameter, part number 24-6337-0007.
This can be ordered from Techni-Tool under Techni-Tool part number 488SO157
Other solder tips
When stripping wire, only strip a tiny little bit of the insulation. Strip no more then a 1/64 of an inch. When the wire gets tinned with solder, the insulation will shrink back more. Try to not expose any more wire then half the length of the solder pad at most. In no case should solder or exposed wire wire ever be outside the boundary of the the solder pad you are attaching a wire to.
Click here for important information on properly Stripping and Tinning wire
In order to keep the wires neat and prevent possible shorts, we recommend lacing the wires into a bundle using lacing cord. Lacing cord is a wax impregnated string used for wire bundling and making harnesses. There are many choices of lacing cord available from Digikey www.digikey.com.
We use part number 802534B BK032-ND