Intermountain U18B

Scale:
HO Scale


WOWKit used in this installation

WDK-INT-1

Which includes the following items:

Decoder
Motherboard
Speaker Kit


DXI Installation

This was performed by our friends from DCC Xpress installations. 
They offer high quality WOWSound installations for a flat rate complete with free return shipping! 
You can find them at: www.dxinstalls.com

This installation is for a HO-Scale Intermountain U18B using a TCS IB-MB2 with a built in KA2 Keep Alive® device and WOW121-Diesel decoder.

HO-Scale Intermountain U18B prior to TCS IB-MB2 and WOW121-Diesel decoder installation
HO-Scale Intermountain U18B prior to TCS IB-MB2 and WOW121-Diesel decoder installation




In order to remove the shell, we must first remove the front and rear couplers and their housings.
In order to remove the shell, we must first remove the front and rear couplers and their housings.


With the couplers and their housings removed, the shell can be lifted up and off of the locomotives chassis.
With the couplers and their housings removed, the shell can be lifted up and off of the locomotives chassis.


With the shell removed, we can now unplug all the JST connections.

Next, remove the four screws securing the factory light board.
With the shell removed, we can now unplug all the JST connections. Next, remove the four screws securing the factory light board.


With the factory light board removed, we're left with two long screws (front) and two short screws (rear).
With the factory light board removed, we're left with two long screws (front) and two short screws (rear).




Additionally, we are left with a shim bracket (front), which we will reuse along with the four screws in the next step.
Additionally, we are left with a shim bracket (front), which we will reuse along with the four screws in the next step.


Next, place the TCS IB-MB2 in its mounting place and secure using the four screws and front shim.

Now you can solder the 2-Pin JST speaker connection harness to your speaker, and mount your speaker in the enclosure.
Next, place the TCS IB-MB2 in its mounting place and secure using the four screws and front shim. Now you can solder the 2-Pin JST speaker connection harness to your speaker, and mount your speaker in the enclosure.


Mount the speaker behind the motherboard in the cutout in the frame (we used hot glue, but you may be able to use screws), plug the JST connectors into the IB-MB2 (according to the diagram that came with the motherboard literature), and plug-in the WOW121-Diesel decoder.
Mount the speaker behind the motherboard in the cutout in the frame (we used hot glue, but you may be able to use screws), plug the JST connectors into the IB-MB2 (according to the diagram that came with the motherboard literature), and plug-in the WOW121-Diesel decoder.


For ease of putting the locomotives shell back on, we used some kapton tape to secure the wires and keep them out of the way.

Finally, place the locomotives shell back on and reintsall the front and rear couplers and their housings.

Note: In this install, we decided to use the factory speaker and baffel.

You have now installed a TCS IB-MB2 with a built in KA2 Keep Alive® and WOW121-Diesel decoder into your HO-Scale Intermountain U18B.
For ease of putting the locomotives shell back on, we used some kapton tape to secure the wires and keep them out of the way. Finally, place the locomotives shell back on and reintsall the front and rear couplers and their housings. Note: In this install, we decided to use the factory speaker and baffel. You have now installed a TCS IB-MB2 with a built in KA2 Keep Alive® and WOW121-Diesel decoder into your HO-Scale Intermountain U18B.



Important Soldering Tip

Please do not use any flux either liquid or paste on the mother board. It will damage it. Use only Rosin core solder approved for electronics use. 
We recommend to use only Kester "44" rosin core, SN63PB37, .015" diameter, part number 24-6337-0007.
This can be ordered from Techni-Tool under Techni-Tool part number 488SO157
http://www.techni-tool.com

Other solder tips

When stripping wire, only strip a tiny little bit of the insulation. Strip no more then a 1/64 of an inch. When the wire gets tinned with solder, the insulation will shrink back more. Try to not expose any more wire then half the length of the solder pad at most. In no case should solder or exposed wire wire ever be outside the boundary of the the solder pad you are attaching a wire to.
Click here for important information on properly Stripping and Tinning wire