Bowser C630M

Scale:
HO Scale


WOWKit used in this installation

WDK-INT-1

Which includes the following items:

Decoder
Motherboard
Speaker Kit


This installation documentation is for the Bowser C630M. This installation uses the WDK-INT-1 Kit which includes the IB-MB2, WOW121-Diesel decoder, and INT-SH1 with 2-pin speaker connector. This installation also uses the 6-Pin JST INT-WH connector harness. This installation was performed by TCS.

The Bowser C630M prior to installation.
The Bowser C630M prior to installation.






Begin this installation by pulling the screws on each coupler as highlighted in red above and then removing the coupler boxes  as well as the spring cover. Grasp the sides and each end of the shell and gentle pull out to release and lift it from the frame.
Begin this installation by pulling the screws on each coupler as highlighted in red above and then removing the coupler boxes as well as the spring cover. Grasp the sides and each end of the shell and gentle pull out to release and lift it from the frame.


Shown with the shell removed. Snip the plastic wire tie to release the wires, remove the four screws indicated above in red and unplug the wire connectors from the board. Remove the board from the frame, taking note of the wiring layout.
Shown with the shell removed. Snip the plastic wire tie to release the wires, remove the four screws indicated above in red and unplug the wire connectors from the board. Remove the board from the frame, taking note of the wiring layout.


With the original lighting board removed.
With the original lighting board removed.


Attach the new IB-MB1 motherboard with the same screws and preliminarily plug in the wiring connections.
Attach the new IB-MB1 motherboard with the same screws and preliminarily plug in the wiring connections.


Clip off the original lighting connector plug as shown above to facilitate wiring the lighting for the IB-MB1 motherboard.
Clip off the original lighting connector plug as shown above to facilitate wiring the lighting for the IB-MB1 motherboard.


To allow correct connection and individual functions from the IB-MB1 motherboard, in this installation it was necessary to separate the wiring  path by cutting a trace on the original front lighting circuit board as shown as red/blue stripes in the above photo.
To allow correct connection and individual functions from the IB-MB1 motherboard, in this installation it was necessary to separate the wiring path by cutting a trace on the original front lighting circuit board as shown as red/blue stripes in the above photo.




The leads soldered to the front (left) and back (right) lighting boards shown above.
The leads soldered to the front (left) and back (right) lighting boards shown above.


Splice these lighting leads into the new connector and plug this connector onto the IB-MB1 according to the included wiring diagram.
Splice these lighting leads into the new connector and plug this connector onto the IB-MB1 according to the included wiring diagram.


Insert the 35mm x 16mm speaker into the INT-SH1 enclosure and mount this assembly to the frame with the provided screws. 
Plug the speaker connector into the motherboard. We secured the wires at this end of the locomotive to the frame using Kapton tape.
If your speaker enclosure installation covers the portholes on the enclosure, we recommend adding new port hole(s) similar to the original porting. Be sure that the new portholes are the same size and amount of the original and are vented freely into the locomotive We have found introducing a port of the correct size greatly increases the volume and sound quality of the installation. Too much or too little porting decreases the sound quality.
Insert the 35mm x 16mm speaker into the INT-SH1 enclosure and mount this assembly to the frame with the provided screws. Plug the speaker connector into the motherboard. We secured the wires at this end of the locomotive to the frame using Kapton tape. If your speaker enclosure installation covers the portholes on the enclosure, we recommend adding new port hole(s) similar to the original porting. Be sure that the new portholes are the same size and amount of the original and are vented freely into the locomotive We have found introducing a port of the correct size greatly increases the volume and sound quality of the installation. Too much or too little porting decreases the sound quality.


Lastly, in order to keep the wires neat and prevent possible shorts, lace the wires into a bundle using lacing cord. You can now reassemble the shell and couplers and your WOWSound equipped Bowser C630M locomotive in ready to roll!
Lastly, in order to keep the wires neat and prevent possible shorts, lace the wires into a bundle using lacing cord. You can now reassemble the shell and couplers and your WOWSound equipped Bowser C630M locomotive in ready to roll!



Important Soldering Tip

Please do not use any flux either liquid or paste on the mother board. It will damage it. Use only Rosin core solder approved for electronics use. 
We recommend to use only Kester "44" rosin core, SN63PB37, .015" diameter, part number 24-6337-0007.
This can be ordered from Techni-Tool under Techni-Tool part number 488SO157
http://www.techni-tool.com

Other solder tips

When stripping wire, only strip a tiny little bit of the insulation. Strip no more then a 1/64 of an inch. When the wire gets tinned with solder, the insulation will shrink back more. Try to not expose any more wire then half the length of the solder pad at most. In no case should solder or exposed wire wire ever be outside the boundary of the the solder pad you are attaching a wire to.
Click here for important information on properly Stripping and Tinning wire