This installation is for a HO Scale Atlas EMD MP-15DC using a TCS WOW121-Diesel Decoder, AK-MB1 Motherboard with built in Keep Alive®
and UNIV-SH4-C WOWSpeaker by TCS.
HO-Scale Atlas EMD MP-15DC shown prior to installation.
To start off this install, we must first remove the front and rear coupler screws highlighted above in red and their housings.
With the couplers removed, gently squeeze the top shell along each side of the frame and lift the shell off of the frame.
The Atlas EMD MP-15DC shown with the shell off. Remove the wires from the original lighting board and remove the board from the chassis.
With the original lighting board removed, clip off the connectors, then trim, tin, or lengthen the wires as necessary.
On the front of the chassis, also remove the small front weight and plastic piece containing it. This piece is discarded.
Attach the AK-MB1 and solder the motor and track pickup wires according to your included wiring diagram. You can now see the speaker frame opening
at the front of the chassis.
In this installation, we lengthened the original lighting wire leads and using a small dab of hot melt glue, attached the front LED to the light tube.
The leads for this as well as the rear LED were soldered to the AK-MB1 according to the included wiring diagram
We have found that LED light output is brightest when shinning directly into the end of the light tube, but in some circumstances they may be placed along the length
of the tube as well with satisfactory results. In doing so, white light LED output would be least affected, while non white LED output will be more affected by placement.
A detail photo showing the placement of the front LED into the top front of the shell.
With the lighting in place and using hot melt glue, secure the 25mm x 14mm speaker face down onto the frame opening as shown above.
Solder the speaker wire leads to the AK-MB1.
NOTE: You must be very careful to avoid getting glue on the speaker cone. Glue on the speaker will ultimately cause it to produce no sound and fail.
NOTE: We found that by adding a strip of 3/4" Kapton tape TCS part #KT3 (available in 1/4" to 1" widths under Kapton tape on the order page) surrounding the front frame underneath the speaker mount, there was a significant sound improvement. After placing the tape, with a blunt flat instrument, we burnished it tightly to the frame.
This addition, shown above, contains the sound and creates a resonating chamber, directing it downward and out of the locomotive.
You can now plug in your WOW121 decoder.
Close up the locomotive and reinstall the coupler assemblies. Be sure to be mindful of wire routing and reassembly of the shell as to not damage
or foul the installation. You Atlas EMD MP-15DC is now WOWSound equipped and ready to roll!
Important Soldering Tip
Please do not use any flux either liquid or paste on the mother board. It will damage it. Use only Rosin core solder approved for electronics use.
We recommend to use only Kester "44" rosin core, SN63PB37, .015" diameter, part number 24-6337-0007.
This can be ordered from Techni-Tool under Techni-Tool part number 488SO157
Other solder tips
When stripping wire, only strip a tiny little bit of the insulation. Strip no more then a 1/64 of an inch. When the wire gets tinned with solder, the insulation will shrink back more. Try to not expose any more wire then half the length of the solder pad at most. In no case should solder or exposed wire wire ever be outside the boundary of the the solder pad you are attaching a wire to.
Click here for important information on properly Stripping and Tinning wire
In order to keep the wires neat and prevent possible shorts, we recommend lacing the wires into a bundle using lacing cord. Lacing cord is a wax impregnated string used for wire bundling and making harnesses. There are many choices of lacing cord available from Digikey www.digikey.com.
We use part number 802534B BK032-ND