This installation is for a HO-Scale Walthers Life Like EMD E8A using a TCS WOW121-Diesel Decoder, AK-MB1 Motherboard with built in Keep Alive™, motherboard mounting clip and 32mm WOWSpeaker. We have found there are two frames for this locomotive. This is the low frame version.
The high frame version with additional front lights can be found on our site at here

This was performed by our friends from DCC Xpress installations.
They offer high quality WOWSound installations for a flat rate complete with free return shipping!
You can find them at:

These items are available in the WDK-WAL-1 which was used for this installation.
AK-MB1 Motherboard with Keep Alive™ WOW121-Diesel Decoder 32mm Round WOWSpeaker Motherboard Mounting Clip
Click here for more information on the WDK-WAL-1 and the rest of the WOWDiesel Kits line.

Important Soldering Tip:
Please do not use any flux either liquid or paste on the mother board. It will damage it. Use only Rosin core solder approved for electronics use.
We recommend to use only Kester "44" rosin core, SN63PB37, .015" diameter, part number 24-6337-0007.
This can be ordered from Techni-Tool under Techni-Tool part number 488SO157


The Walthers Life Like EMD E8A with its shell on. To remove the shell, gently pull outwards along each side and lift the shell off of the frame being
careful with the couplers.

Walthers Life Like EMD E8A with the shell off.

Remove the two screws highlighted above in red and this original volume adjustment board.
At the same time, remove the two screws highlighted above in blue and set them aside for later use.

Next, remove the eight screws highlighted above in red from the original decoder board and save them as you will reuse some of them later.
Clip off the connectors on the wires.

Show with the original decoder board removed. The plastic frame platform floor is shown on top of the speakers and covers the entire frame.

Remove the two screws highlighted in red above from the lighting board support that still is on the frame. Discard this piece and these screws.

Finally, remove the two screws highlighted above in red and lift out the cab interior. Save this and these screws for reinstallation.
Now you can remove the entire plastic frame platform floor from the top of the frame to get access to the speakers by carefully lifting it up.

With the plastic frame floor platform removed, remove the two speakers from the frame as we will not be reusing them for this installation.
However, do not discard the original rubber speaker gasket as this will be used for the WOWSpeaker installation.

Shown with the plastic platform floor frame and speakers removed. Trim, tin or lengthen the wire leads as necessary.

Install the new WOWSound 32mm speaker into the open frame, utilizing the original gasket underneath to seal and insulate it against the frame.

Reinstall the plastic floor frame and secure it with the original screws. Mount the motherboard mounting clip into the frame inside of the frame uprights and clip the AK-MB1 onto the motherboard mounting clip. Solder the motor track and speaker leads to the AK-MB1 motherboard according to the included wiring diagram.

In this installation, we found it necessary to add length to the front LED leads. Shown above are these wires which have been spliced in and insulated
with TCS part #1320 Black 3/64" heat shrink tubing. Solder these lighting leads to the AK-MB1 motherboard according to the included wiring diagram.
We attached the front headlight wire (shown in red to white) goes to the forward pad and the marker light lead (here as yellow to green) is to the #1 pad.
The brown to blue lead is to the blue pad. TCS motherboards include on board current limit resistors for LED use.
There is no need to apply external resistors for LED use. 

You can now plug in your WOW121 decoder.

Lastly, in order to keep the wires neat and prevent possible shorts, lace the wires into a bundle using lacing cord, which is a wax impregnated string 
used for wire bundling and making harnesses. There are many choices of lacing cord available from Digikey
We use part number 802534B BK032-ND

Now you can close up the locomotive and reinstall the coupler assemblies. Be sure to be mindful of wire routing and reassembly of the shell as to not damage 
or foul the installation. Your Walthers Life Like EMD E8A is now WOWSound equipped and ready to roll!

Other solder tips: When stripping wire, only strip a tiny little bit of the insulation. Strip no more then a 1/64 of an inch. When the wire gets tinned with solder the insulation will shrink back more. Try to not expose any more wire then half the length of the solder pad at most. In no case should solder or exposed wire wire ever be outside the boundary of the the solder pad you are attaching a wire to.
Click here for important information on properly Stripping and Tinning wire

Like us on Facebook Subscribe to our YouTube Channel Join our newsletter
  Back To Top
Entire contents © Copyright Train Control Systems 2004-2018